
AUTOMOTIVE · ASSEMBLY PART VERIFICATION
Verify the part without putting it down.
The VEGA-X smart glove scans the barcode and takes a photo of the part. TIM INSPECT verifies that it is the right part for that vehicle and free of scratches and defects; the result goes to MES and to the PLC at the station.
Trusted by the world’s leading companies.
Results from an assembly line producing a vehicle every 52 seconds
Results for this deployment are based on the Thread In Motion project report.
THE NEED ON THE FLOOR
Verify the right part at line speed.
On an assembly line the part has to go in quickly, and the record has to show it was the right part for that vehicle. The operator picks up the part and fits it straight onto the vehicle; carrying it to a camera would mean an extra walk and extra time on every vehicle. Build the check into the motion of holding the part.
- 01
Two checks from one photo
Use the same photo to verify that the part is the right one and that it has no scratches or defects. The operator stays at the station.
- 02
Keep going when the barcode fails
If the barcode is damaged, TIM INSPECT reads the number on the part character by character with OCR and can also recognise the part by its shape.
- 03
Do not move on with a faulty part
If the part is wrong or defective, the glove vibrates and a red light comes on. At the same moment a stop signal goes to the PLC at the station.
EXPLORE THE SITUATION
What happens at the station when a part is not OK?
Choose a situation to see what is evaluated in the glove’s photo, how the operator is alerted and what goes to MES and the PLC.

Station 7
- PartCorrect
- SurfaceScratch
- PLCStop
The barcode is read and the part is correct for the vehicle. In the photo, a scratch is detected on the cover of the part.
The glove vibrates and a red light comes on; the operator does not fit the part. An undamaged part is picked up and scanned again.
The photo and result are recorded. A stop signal goes to the PLC; the line does not move on with a faulty part.
Part identityOKMatch to vehicleOKSurface checkNot OK
The glove vibrates and a red light comes on. VEGA-X screen: “Surface defect at station 7.”
HOW IT WORKS
Scan. Verify. Send the result to the line.

Vehicle sequence 0418
- PartABS unit
- IdentityBarcode

Station 7
- PartCorrect
- SurfaceClean
- PLCCorrect


Station 7 · vehicle sequence 0418
- PartABS unit
- MESApproval written
- PLCOK signal
- PhotoStored
Scan the barcode
The operator picks up the part and scans its barcode with VEGA-X. If the barcode cannot be read, identity comes from the number on the part through OCR.
SYSTEM, RECORD AND INTEGRATION
One workflow from the glove to MES and PLC.
Barcode, photo, analysis and line signal come together in one workflow. The photo and result of every check stay in the system, so the record shows which part went into which vehicle.

Barcode and photo
VEGA-X scans the barcode and photographs the part while it is in the operator’s hand.
- DeviceVEGA-X smart glove
- Moment of checkPart in the operator’s hand
- Components
- VEGA-X smart glove
- TIM INSPECT software
- MES integration
- PLC integration
Not dependent on the barcode
Even without a readable barcode, the part is recognised by its number or shape.
Quality check at the same station
Fitting the part and checking its quality happen in one step, in one motion.
Not limited to one part
The method applied to the ABS unit can be carried over to other automotive parts.
See the photo and result of every check in one record, together with the vehicle the part went into. The record shows whether identity was verified by barcode or by OCR, and which part was stopped and why.
APPLICATION FILM
The glove scans and captures. TIM INSPECT verifies.

TIM INSPECT · EXPLORE SOLUTIONS
One platform. 35 applications.
Discover the next opportunity on your floor. Choose a solution area or industry and explore each application visually.
Verification & qualityShipment & Crate Verification
Count passing crates, read their labels and match the load against the shipment list.
Automotive · Logistics & warehousing
Verification & qualityReturned Product Inspection
Identify returned products and record visual checks of damage, dates and product information.
Food & beverage · Retail & e-commerce · Logistics & warehousing
Verification & qualityVoice-Guided Final Inspection
Complete hands-free inspection steps and document findings with voice and photographs.
Automotive · Manufacturing
Verification & qualityCargo Sortation & Pallet Verification
Verify outgoing cargo by checking shipping labels and pallet contents together.
Logistics & warehousing · Aviation
Verification & qualityMetal Part & Label Verification
Match stamped metal-part numbers with crate labels to verify product identity.
Automotive · Manufacturing
Verification & qualityQuick-Connect Verification
Visually check that assembly quick-connects are fully seated and record the result.
Automotive · Manufacturing
Verification & qualityVehicle Label Verification
Read vehicle-specific labels with OCR and compare them with expected production data.
Automotive · Manufacturing
Verification & qualityComponent Assembly Inspection
Visually verify the assembly of components such as retaining rings, washers and plugs.
Automotive · Manufacturing
Verification & qualityProduct & Carton Verification
Combine product, plug, label and carton-content checks before shipment.
Automotive · Manufacturing · Logistics & warehousing
Workplace safetyForklift–Pedestrian Safety
Analyze risky encounters from camera feeds and alert the people involved through AXION.
Manufacturing · Logistics & warehousing
Workplace safetyRestricted-Zone Detection
Detect entry into hazardous areas and alert the worker and responsible team.
Manufacturing · Construction
Workplace safetyPPE Detection
Check the use of helmets, vests and other protective equipment in working areas.
Manufacturing · Construction · Logistics & warehousing
Workplace safetyFire & Smoke Early Warning
Evaluate visible flame and smoke signs in camera feeds and notify the relevant team.
Manufacturing · Logistics & warehousing · Energy & facilities
Workplace safetySpill & Leak Detection
Detect unexpected liquid accumulation and leaks, and notify teams with location information.
Manufacturing · Food & beverage · Energy & facilities
Workplace safetyFallen or Motionless Person Detection
Detect falls or prolonged inactivity to support the assistance workflow.
Manufacturing · Logistics & warehousing · Energy & facilities
Workplace safetyErgonomics & Posture Analysis
Analyze lifting, bending and reaching movements to make risky postures visible.
Manufacturing · Logistics & warehousing
Workplace safetyWorking-at-Height Safety
Use visual checks to assess harness attachment, scaffolding and ladder use.
Construction · Energy & facilities · Manufacturing
Workplace safetyLockout/Tagout Verification
Verify isolation steps with photographs to manage checks before maintenance.
Manufacturing · Energy & facilities
Workplace safetyEmergency Exit & Route Monitoring
Detect obstructions blocking emergency exits and access routes through camera feeds.
Manufacturing · Logistics & warehousing · Retail & e-commerce
Workplace safetyLoading Dock Safety
Check truck position, wheel chocks and dock conditions to flag risky loading situations.
Logistics & warehousing · Manufacturing
Operational efficiencyAssembly Sequence Verification
Monitor the defined assembly sequence and flag missed or out-of-order steps.
Automotive · Manufacturing
Operational efficiencyCycle Time & Microstops
Measure station cycles and brief stops from video to reveal deviations in workflow.
Automotive · Manufacturing
Operational efficiencyMachine Utilization
Assess running and waiting periods visually and notify the relevant team of stops.
Manufacturing · Automotive
Operational efficiencyDock & Door Monitoring
Track vehicle arrivals, door use and loading progress in one workflow.
Logistics & warehousing · Manufacturing
Operational efficiencyFour-Side Pallet Scanning
Read labels across pallet faces during a pass and match them against the order list.
Logistics & warehousing · Retail & e-commerce · Food & beverage
Operational efficiencyDimensioning
Check carton and pallet dimensions with vision and laser measurement and create a record.
Logistics & warehousing · Retail & e-commerce
Operational efficiencyDamage Detection
Document carton, pallet and container damage with photographs at entry and exit points.
Logistics & warehousing · Retail & e-commerce · Manufacturing
Operational efficiencyInventory Counting
Read shelf and pallet labels to reveal empty locations and placement mismatches.
Logistics & warehousing · Retail & e-commerce · Manufacturing
Operational efficiencyLicense Plate & Container OCR
Read vehicle and container numbers and match them with appointment and shipment records.
Logistics & warehousing · Manufacturing
Operational efficiencyConveyor Jam Detection
Detect conveyor build-ups and jams and notify the person who can respond.
Logistics & warehousing · Manufacturing · Food & beverage
Facility monitoringGauge & Meter Reading
Read analog gauges from images, record values and notify teams of threshold exceptions.
Manufacturing · Energy & facilities
Facility monitoringMaintenance Rounds
Follow inspection points step by step and document findings with photographs and voice.
Manufacturing · Energy & facilities
Facility monitoringUnauthorized Entry
Monitor designated-area entry and tailgating and notify the security team.
Manufacturing · Logistics & warehousing · Retail & e-commerce
Facility monitoringEnvironmental Monitoring
Monitor visible emissions, dust and waste-sorting conditions through camera feeds.
Manufacturing · Energy & facilitiesFAQ
Questions, answered
Assembly Part Verification is a quality control solution on Thread In Motion’s TIM INSPECT platform that checks part identity and surface defects using the barcode and photo from the VEGA-X smart glove. Wrong or defective parts trigger glove vibration and a PLC stop signal; results are written to MES.
With TIM INSPECT, Assembly Part Verification works in four steps: 1) Scan the barcode: The operator picks up the part and scans its barcode with VEGA-X. If the barcode cannot be read, identity comes from the number on the part through OCR. 2) Verify with a photo: The glove takes a photo of the part. TIM INSPECT verifies that it belongs to that vehicle and checks it for scratches and defects. 3) Stop when it is not OK: If the part is wrong or defective, the glove vibrates, a red light comes on and a stop signal goes to the PLC. 4) Write the record to MES: The approval and the photo are written to MES and an OK signal goes to the PLC. The part becomes traceable together with the vehicle it went into.
Components used: VEGA-X smart glove, TIM INSPECT software, MES integration and PLC integration. Barcode, photo, analysis and line signal come together in one workflow. The photo and result of every check stay in the system, so the record shows which part went into which vehicle.
The operator picks up the part and fits it straight onto the vehicle. Carrying it to a camera would add an extra movement, an extra walk and lost time on every vehicle. With VEGA-X the check happens within the motion of holding the part, so the operator never leaves the job.
The work does not stop. TIM INSPECT reads the number on the part from the photo, character by character with OCR, and compares it with the part the vehicle expects. Where needed, the part can also be recognised by its shape. Parts normally carry a barcode; OCR is for the cases where it cannot be read.
Scratches and defects on the part are analysed from the photo. The same photo also verifies that it is the right part for that vehicle, so fitting the part and checking its quality happen together at the station.
TIM INSPECT sends a stop signal to the PLC next to the station; if the part is OK, an OK signal is sent instead. The line waits for this signal from the PLC. How the line responds is planned together with the logic on the PLC side.
This deployment went live on the ABS unit. The same method can be applied to more than one automotive part. The scope is assessed together with the parts you want to verify and your line speed.

YOUR SITE
Let’s review your assembly stations together.
Let’s look at the parts to verify, your MES and PLC connections and your line speed, then define the pilot scope and the results to measure from the start.
























