OPERATIONAL EFFICIENCY · ASSEMBLY SEQUENCE
Verify each assembly step as it happens.
Follow manual assembly from the continuous feed of an overhead station camera and confirm it runs in the defined order and method. When a step is skipped or the wrong part is picked, AXION tells the worker which step is missing.
Trusted by the world’s leading companies.
THE NEED ON THE FLOOR
Catch a skipped step at the station, not at end of line.
In manual assembly, a skipped step usually surfaces at the end of the line and sometimes in the field. Standard work instructions sit on paper, and whether they are followed is not measured. A single photo cannot show that a step was done. TIM INSPECT watches the station on continuous video and evaluates the whole process.
- 01
Define standard work in the system
Define the steps, their order, the part to pick, the tool and the method. The camera follows the same sequence on every unit.
- 02
Tell the worker right away
When a step is skipped or the wrong part is picked, the worker’s AXION vibrates and says which step is missing.
- 03
Keep a step record for every unit
The step record and video of each completed unit are stored. Step times are reported and the record goes to the MES per unit.
EXPLORE THE SITUATION
What happens when a step is skipped?
Choose a situation to see which step the camera flags, the alert the worker receives and how the unit is released to the next station.

Station 4 · Cover assembly
- 3 · GasketSkipped
- 4 · PlateStarted
After tightening the gear, the worker moves on to the plate without placing the gasket; step three is skipped.
The worker’s AXION vibrates and names the missing step. The worker goes back, places the gasket and continues from there.
Step three turns red in the step list. The unit is not released to the next station until the gap is closed.
1 · Place the gearDone2 · Tighten the gearDone3 · Place the gasketSkipped4 · Place the plateUp next5 · Seat with both handsUp next

Voice alert: “Step three is missing. Place the gasket.”
HOW IT WORKS
Define. Watch. Alert on deviation.
Station 4 · Standard work
- Steps5
- OrderMandatory
- ToolRatchet wrench
- MethodTwo-hand seating

Step 2 · Tightening
- StatusIn progress
- Time6 s


Unit step record
- UnitKM-20417
- Steps5 / 5
- Cycle48 s
- VideoStored
Define standard work
Standard work steps are defined in the system: the order of steps, the part to pick, the tool and the method.
SYSTEM, RECORD AND INTEGRATION
Connect the step record to your production system.
The standard work definition, the steps marked by the camera and the alert to the worker come together in one workflow. The step record goes to the MES per unit; where needed, a release or stop signal is sent to the line PLC.

Station view
Hands, parts and tools seen by the overhead station camera.
- SourceOverhead fixed camera
- CoverageWork area
- Components
- Overhead fixed camera
- TIM INSPECT software
- AXION
- MES connection
- Optional PLC signal
The whole process
A photo shows the result; video shows how the work was done.
Built for error prevention
The aim is to catch a missing step at the station, not to rate worker performance.
Privacy-aware design
The work zone and the steps are observed, not identity; images are filtered.
Review in one record which steps a unit went through and in what order, where a deviation opened and when it closed. Use the step time report to revisit work instructions and station layout on the basis of concrete records.
SOLUTION FILM
The camera follows the steps. AXION tells the worker which one is missing.

TIM INSPECT · EXPLORE SOLUTIONS
One platform. 35 applications.
Discover the next opportunity on your floor. Choose a solution area or industry and explore each application visually.
Operational efficiencyCycle Time & Microstops
Measure station cycles and brief stops from video to reveal deviations in workflow.
Automotive · Manufacturing
Operational efficiencyMachine Utilization
Assess running and waiting periods visually and notify the relevant team of stops.
Manufacturing · Automotive
Operational efficiencyDock & Door Monitoring
Track vehicle arrivals, door use and loading progress in one workflow.
Logistics & warehousing · Manufacturing
Operational efficiencyFour-Side Pallet Scanning
Read labels across pallet faces during a pass and match them against the order list.
Logistics & warehousing · Retail & e-commerce · Food & beverage
Operational efficiencyDimensioning
Check carton and pallet dimensions with vision and laser measurement and create a record.
Logistics & warehousing · Retail & e-commerce
Operational efficiencyDamage Detection
Document carton, pallet and container damage with photographs at entry and exit points.
Logistics & warehousing · Retail & e-commerce · Manufacturing
Operational efficiencyInventory Counting
Read shelf and pallet labels to reveal empty locations and placement mismatches.
Logistics & warehousing · Retail & e-commerce · Manufacturing
Operational efficiencyLicense Plate & Container OCR
Read vehicle and container numbers and match them with appointment and shipment records.
Logistics & warehousing · Manufacturing
Operational efficiencyConveyor Jam Detection
Detect conveyor build-ups and jams and notify the person who can respond.
Logistics & warehousing · Manufacturing · Food & beverage
Verification & qualityShipment & Crate Verification
Count passing crates, read their labels and match the load against the shipment list.
Automotive · Logistics & warehousing
Verification & qualityReturned Product Inspection
Identify returned products and record visual checks of damage, dates and product information.
Food & beverage · Retail & e-commerce · Logistics & warehousing
Verification & qualityVoice-Guided Final Inspection
Complete hands-free inspection steps and document findings with voice and photographs.
Automotive · Manufacturing
Verification & qualityAssembly Part Verification
Check parts, labels and surfaces during assembly and send the result to production systems.
Automotive · Manufacturing
Verification & qualityCargo Sortation & Pallet Verification
Verify outgoing cargo by checking shipping labels and pallet contents together.
Logistics & warehousing · Aviation
Verification & qualityMetal Part & Label Verification
Match stamped metal-part numbers with crate labels to verify product identity.
Automotive · Manufacturing
Verification & qualityQuick-Connect Verification
Visually check that assembly quick-connects are fully seated and record the result.
Automotive · Manufacturing
Verification & qualityVehicle Label Verification
Read vehicle-specific labels with OCR and compare them with expected production data.
Automotive · Manufacturing
Verification & qualityComponent Assembly Inspection
Visually verify the assembly of components such as retaining rings, washers and plugs.
Automotive · Manufacturing
Verification & qualityProduct & Carton Verification
Combine product, plug, label and carton-content checks before shipment.
Automotive · Manufacturing · Logistics & warehousing
Workplace safetyForklift–Pedestrian Safety
Analyze risky encounters from camera feeds and alert the people involved through AXION.
Manufacturing · Logistics & warehousing
Workplace safetyRestricted-Zone Detection
Detect entry into hazardous areas and alert the worker and responsible team.
Manufacturing · Construction
Workplace safetyPPE Detection
Check the use of helmets, vests and other protective equipment in working areas.
Manufacturing · Construction · Logistics & warehousing
Workplace safetyFire & Smoke Early Warning
Evaluate visible flame and smoke signs in camera feeds and notify the relevant team.
Manufacturing · Logistics & warehousing · Energy & facilities
Workplace safetySpill & Leak Detection
Detect unexpected liquid accumulation and leaks, and notify teams with location information.
Manufacturing · Food & beverage · Energy & facilities
Workplace safetyFallen or Motionless Person Detection
Detect falls or prolonged inactivity to support the assistance workflow.
Manufacturing · Logistics & warehousing · Energy & facilities
Workplace safetyErgonomics & Posture Analysis
Analyze lifting, bending and reaching movements to make risky postures visible.
Manufacturing · Logistics & warehousing
Workplace safetyWorking-at-Height Safety
Use visual checks to assess harness attachment, scaffolding and ladder use.
Construction · Energy & facilities · Manufacturing
Workplace safetyLockout/Tagout Verification
Verify isolation steps with photographs to manage checks before maintenance.
Manufacturing · Energy & facilities
Workplace safetyEmergency Exit & Route Monitoring
Detect obstructions blocking emergency exits and access routes through camera feeds.
Manufacturing · Logistics & warehousing · Retail & e-commerce
Workplace safetyLoading Dock Safety
Check truck position, wheel chocks and dock conditions to flag risky loading situations.
Logistics & warehousing · Manufacturing
Facility monitoringGauge & Meter Reading
Read analog gauges from images, record values and notify teams of threshold exceptions.
Manufacturing · Energy & facilities
Facility monitoringMaintenance Rounds
Follow inspection points step by step and document findings with photographs and voice.
Manufacturing · Energy & facilities
Facility monitoringUnauthorized Entry
Monitor designated-area entry and tailgating and notify the security team.
Manufacturing · Logistics & warehousing · Retail & e-commerce
Facility monitoringEnvironmental Monitoring
Monitor visible emissions, dust and waste-sorting conditions through camera feeds.
Manufacturing · Energy & facilitiesFAQ
Questions, answered
Assembly Sequence Verification is an operational efficiency solution on Thread In Motion’s TIM INSPECT platform that verifies manual assembly step order and method with an overhead station camera. A skipped step or wrong part triggers an alert on the worker’s AXION; each unit’s step record goes to the MES.
With TIM INSPECT, Assembly Sequence Verification works in four steps: 1) Define standard work: Standard work steps are defined in the system: the order of steps, the part to pick, the tool and the method. 2) Mark every step: The camera watches the station without interruption. TIM INSPECT marks each step as it happens and measures its duration. 3) Alert on deviation: If a step is skipped or the wrong part is picked, the worker’s AXION vibrates and says which step is missing. 4) Keep the record: The step record and video of each completed unit are stored. The unit is released to the next station once no step is open.
Components used: overhead fixed camera, TIM INSPECT software, AXION, MES connection and optional PLC signal. The standard work definition, the steps marked by the camera and the alert to the worker come together in one workflow. The step record goes to the MES per unit; where needed, a release or stop signal is sent to the line PLC.
No. The purpose is error prevention: catching a skipped step or a wrong part before the unit leaves the station. Step times are reported to improve work instructions and station layout; they are not presented as an individual performance assessment.
The overhead station camera looks at the work area, the hands, the part and the tool. The zone and the actions are observed, not identity, and images are filtered. Which footage is kept and for how long is defined at the start of the deployment in line with KVKK and GDPR requirements.
A single photo only shows the result; it cannot show the order or the method by which a step was done. Continuous video makes it possible to assess which part the hand picks, where it is fitted, the tool used and the duration of each step.
Skipped or repeated steps, a broken sequence, a wrong part, a different tool and work that does not follow the defined method are within the scope of this scenario. For example, a part that must be fitted with both hands but is fitted with one is flagged. The scope is finalised around the camera view at the station.
The alert stays open and the unit is not released to the next station until the missing step is completed. Where needed, a release or stop signal can be sent to the line PLC; the scope of that connection is planned around the automation infrastructure on site.

YOUR SITE
Let’s define a pilot on one of your assembly stations.
Let’s review your work instructions, station layout and camera view together, then define the pilot scope and the metrics to measure at the end of the pilot from the start.
























