Get a demo

Working at Height Safety: How to Verify the Harness Is Attached

5 min read
Worker sitting on scaffold tubes at height without a safety harness

Working at height safety depends on a detail that is easy to miss: a safety harness only protects a worker if the hook is actually attached to an anchor point. Vision AI can check this continuously, not just during a spot check: cameras watch the platforms, scaffolds and ladders you define, see the person, the harness and the hook, and alert the worker on their wearable when something is missing. The Working-at-Height Safety solution page shows the full alert and record flow.

This guide covers why harness checks fail in practice, how camera-based monitoring of working-at-height areas works and what to test on site before a pilot.

Why falls from height remain such a serious risk

Falls from height are among the accident types with the most severe outcomes in construction, maintenance and manufacturing. The UK Health and Safety Executive's working at height guidance sets out a clear hierarchy: avoid work at height where possible, prevent falls where it cannot be avoided, and minimise the consequences where the risk remains. Harnesses belong to that last layer, which makes using them correctly critical.

The everyday problem is simple. A worker climbs onto a scaffold to finish a quick job, the harness is on but the lanyard is not clipped, or they unclip to move and forget to reattach. Wearing a harness and being attached are two different things, and only the second one stops a fall.

How working-at-height checks are done today

  • Work permits: a permit defines who works at height, where and with which precautions. It confirms the plan, not what happens two hours later on the platform.
  • Supervisor walk-arounds: safety officers visit areas and correct what they see. Their checks are momentary and infrequent, especially on large sites or several jobs at once.
  • Pre-use inspections: harnesses, lanyards and scaffolds are inspected before use. These checks are about the equipment's condition, not whether it is used correctly during the task.
  • Training and toolbox talks: necessary, but under time pressure people still take shortcuts.

All of these are valuable, yet none of them watches the moment that matters: a person at height without the hook attached.

How vision AI checks harness and hook attachment

On the TIM INSPECT platform, working-at-height safety uses fixed cameras and follows four steps:

  1. Define the working-at-height area. Platforms, scaffolds, ladders and slab edges are marked in the camera view. The check applies only to people inside those areas.
  2. Detect the person and the harness. Cameras assess the person in the area, the safety harness and whether the hook is attached. Status is observed, not identity.
  3. Alert the worker first. If something is missing, the worker's AXION wearable vibrates and gives an alert such as "No safety harness. Put it on and attach the hook." If the issue continues, the safety officer is notified.
  4. Record the event. Each event is recorded with its area and duration and matched with the permit in the work permit system. Violation records are kept by area.

Besides a missing harness or an unattached hook, the scope includes approaching an edge without a guardrail and incorrect ladder use. The system does not stop work by itself; it alerts and records, and the people on site take action.

From spot checks to continuous monitoring

Because every alert is recorded with where it was opened, how long it lasted and how it closed, you can look at violation records alongside work permits. Patterns become visible: a scaffold where hooks are often left unclipped, a ladder used as a work platform, a time of day when shortcuts happen. Those are the places to focus training, anchor points or a change in method.

What to test before installation

Camera placement and distance

Small details such as a hook are hard to see from a distant camera. Camera placement is therefore tested on site: viewing angle and distance are chosen so that harness and hook can be told apart. The scope is settled through these tests before the pilot, not assumed in advance.

Temporary and changing work areas

Scaffolds go up and come down, and maintenance work at height moves around a plant. Agree which areas are permanent, which are temporary and how new areas will be added to the camera view when a job starts.

Lighting and weather

Outdoor work brings glare, backlight and changing weather; indoor work can mean dark roof areas. Include these conditions in the on-site tests.

Privacy

The system observes the zone a person is in and what they do, not who they are. Images are filtered and only the event moment is kept; the setup is designed around GDPR and KVKK requirements from the outset.

Work permit integration

Matching events with permits is what turns alerts into management information. The integration scope is planned around the permit system used on site. If you also want to check helmets and vests in the same areas, PPE Detection can run on the same camera views.

FAQ

Can a camera really see whether a hook is attached?

Small details are hard to see from far away, so camera placement is tested on site and chosen so that harness and hook can be distinguished. The scope is confirmed before the pilot.

Who receives the alert?

The worker's AXION first. If the issue is not fixed, the safety officer is notified.

Does the system stop the work?

No. It alerts and records the event; stopping work remains a decision for people on site.

Does it work with our work permit system?

Event records can be matched with permits; the integration is planned around the permit system you use.

Next step

If you want to test camera positions and hook visibility in your own working-at-height areas, request a demo and we will plan the on-site trial together; more detail is on the solution page.

Share this article LinkedIn X
Written by Ece Tanışık
Thread in Motion

See TIM on your own floor

Wearable scanners, Physical AI wearables and vision AI for frontline operations. Let us show you how they fit your process.

Get a demo

Keep reading

Chat on WhatsApp WhatsApp'tan yazın