Pre-shipment carton verification is the last chance to stop a wrong product, a product of the wrong size or a carton with a part missing before it reaches the customer. The most dependable approach combines hand-held checks for plugs and labels, a laser measurement for product height and a camera that watches the carton for the whole time it is being filled, not just in one photo. TIM INSPECT Product & Carton Verification brings these checks together at a single packing station.
What goes wrong at the packing station
Packing looks simple: finished products go into the customer's carton and the carton ships. In practice, three errors keep reappearing at this stage. A product of the wrong height is packed with the others. The wrong product, or a product meant for another customer, ends up in the carton. Or the carton leaves with one part missing, a plug left out or a layer pad forgotten.
Each of these turns into a complaint at the customer's receiving dock, and in automotive supply chains a complaint often triggers sorting, extra checks and a closer look at every following delivery. The packing station is where these errors are cheapest to catch, provided the check cannot be bypassed.
Why traditional packing checks fall short
- Checks left to the operator's attention. The operator checks the product by eye while packing. Under time pressure and with similar-looking variants, small differences are easy to miss.
- Repeat checks at the next station. Many lines re-check the label and other points at a following station. That adds labour and time, and it still relies on people.
- Single-photo verification. A photo of the open carton seems objective, but it only proves one moment. A product can be placed in the carton, photographed and taken back out; the photo says "correct" and the carton ships incomplete.
How vision AI verifies product and carton at one station
The solution assigns each check to the technology that suits it best and runs them in one workflow. Which customer the product belongs to, and the expected values, come from MES.
- Check plugs and label. The operator looks at the product with the VEGA-X smart glove: are the plugs in place, is the label correct for this customer and product?
- Measure height by laser. A smart laser system on the table measures the product's height. A product of the wrong height is set aside before it is packed.
- Watch the carton as it fills. A fixed camera above the carton watches without a break: how many parts went in, whether their plugs are present, whether layer pads were placed, and whether any part was taken back out.
- Alert, label, confirm. On any error the glove vibrates and the system is notified. Once every check is complete, the customer's shipping label is printed and the operator finishes with a barcode scan; the label is also confirmed with vision.
Imagine a product on the table whose label code does not match the customer and product information from MES. The glove sees the difference and vibrates, the VEGA-X screen shows "Label mismatch", and the operator sets the product aside and brings the right one. The wrong product never enters the carton, and the error is reported to the system at the same moment.
Why continuous video matters
Watching the carton for the whole time it is filled is what makes the verification hard to bypass. The system knows everything that happened, not one moment. A carton that leaves the area before the part count or the plug check is complete is flagged as not OK. For every carton, a video record and event history are kept: which part went in when, which one was taken out, and in what state the carton was closed.
Results from a deployment
At an automotive supplier, product and carton verification reached 99% height measurement accuracy, made the process 50% faster and achieved 100% customer satisfaction. The repeat check at the next station was no longer needed. These results relate to that deployment and are based on the Thread In Motion project report.
What to plan before setting up the station
- Which check runs where. Decide which checks belong on the glove, which on the laser and which on the camera. Plugs and labels suit the hand, dimensions suit the laser, carton contents suit continuous video.
- MES connection. The station needs the customer and the expected values for each product, and it prints the customer's label only when all checks pass. Map these data flows first.
- Carton layout. Number of parts, layers and pads per carton define what the camera counts. Standard layouts make the rules simpler.
- Camera position and light. The fixed camera needs a clear view into the carton from above for the whole filling process, without the operator's arms blocking the critical area for long.
- Evidence use. Agree who will review carton records and how they will be used when a customer raises a question.
If your shipments go out in crates or returnable containers rather than cartons, see Shipment & Crate Verification. Both are part of the TIM INSPECT platform, which writes results back to systems such as SAP, MES or WMS.
FAQ
Why use continuous video instead of a photo?
A product can be placed, photographed and removed again, so a photo proves only one moment. Continuous video follows the whole filling process and records it.
Which check is done with which technology?
Plugs and label are checked with VEGA-X, height with the smart laser, and carton contents with continuous video from the fixed camera. The shipping label is confirmed with a barcode scan and vision.
How is the operator alerted to an error?
The glove vibrates, both for hand checks and for errors found by the video analysis, and the error is reported to the system at the same time.
What does the MES integration provide?
It tells the station which customer the product belongs to and which values to expect, and it allows the customer's shipping label to be printed once every check passes.
Next step
If you want to bring your pre-shipment checks to one station, request a demo and we can review your product, carton layout and MES connection together.