Get a demo

TIM INSPECT · Automotive & manufacturing

Assembly Error-Proofing with Vision AI

Stop the wrong, missing or unseated part at the station, not at end-of-line.

Assembly error-proofing with vision AI checks each part and step as it is assembled, so a wrong, missing or unseated part is stopped at the station instead of being found later. TIM INSPECT captures the image with a fixed camera, AXION or the VEGA-X glove, decides in seconds, alerts the operator and writes the result to MES, SAP or PLC.

Assembly line part checked by TIM INSPECT vision AI before it moves on
12.8 million+ assembly inspections in a single application
  • See, decide, alert, recordOne loop closes from image to system record.
  • Where cameras can't seeWearables check parts in the hand and hard-to-reach spots.
  • Writes to your systemsExpected value in, result and evidence photo out.

The problem

Why assembly errors still reach the customer

Visual inspection depends on the person and the shift and leaves no evidence. Paper checklists record that a step was signed, not that it was done. Fixed cameras help, but they look from one angle and cannot see the part in the operator's hand or the connector behind a bracket.

Inconsistent checks

Results vary by operator and shift, and visual checks cannot keep pace with line speed.

Blind angles

A fixed camera misses in-hand parts, hidden fasteners and hard-to-reach connections.

No proof

When a complaint arrives, there is no photo showing how that unit was built.

The solution

Error-proofing that closes the loop at the station

TIM INSPECT is an operational vision AI platform. Most vision products stop at detection; TIM INSPECT also alerts the right person, stops the process when needed and writes the result to your systems. It runs on your own cameras or on AXION and VEGA-X.

Read

Labels, numbers stamped in metal and part numbers, matched against production data.

Recognize

Parts without a barcode, identified by their appearance.

Inspect

Is the part in place and fully seated; is anything missing or damaged.

Verify the sequence

Missed or out-of-order assembly steps are flagged as they happen.

Alert and stop

Vibration, sound and light to the operator; a stop signal to the PLC.

Record

Every operation saved with an evidence photo, ready for audits.

How it works

How vision AI error-proofing works on the line

Every TIM INSPECT solution runs the same four-step loop.

  1. See

    A fixed camera, AXION or the VEGA-X glove captures the part, label or step.

  2. Decide

    TIM's own models compare it with the expected value from MES or SAP in seconds.

  3. Alert

    The operator gets OK or NOK by vibration, sound, light or screen; the PLC can stop the line.

  4. Record

    The result and evidence photo are written to your systems, and the record stays open until the error is fixed.

Field results

Assembly applications on record

Figures from the project reports of TIM INSPECT field applications.

Customer proof

Automotive manufacturers using vision AI at the station

Published stories from automotive production and Tier-1 suppliers.

Automotive

Ford

TIM INSPECT and VEGA-X digitized quality control: operators captured data hands-free while TIM INSPECT validated each step in real time.

  • 100%Traceability
  • 50%Speed
  • 0%Errors
Read the story

Tier-1 supplier

Tirsan Kardan

Operators captured images from any angle with VEGA-X; AI models returned instant pass or fail across complex drivetrain parts.

  • 100%Coverage
  • 100%Accuracy
  • 0%Errors
Read the story

Automotive

Assan Hanil

AI image analysis with VEGA-X reached hard-to-reach areas and verified each component across all surfaces.

  • 100%Coverage
  • 100%Accuracy
  • 100%Traceability
Read the story

With TIM wearables on the line, Renault and Stellantis cut assembly verification from 8 to 4 seconds.

Video

Wearable verification on an assembly line

Stellantis and TIM on a high-volume automotive line.

FAQ

Assembly error-proofing FAQ

What is assembly error-proofing?

Error-proofing, or poka-yoke, prevents assembly mistakes from moving downstream. With vision AI, each part, label or step is checked by image at the station and a wrong or missing part is stopped before the unit moves on.

How is this different from a fixed camera system?

A fixed camera looks from one angle and cannot see the part in the operator's hand. TIM INSPECT adds wearables such as AXION and VEGA-X, and it does not stop at detection: it alerts the operator, can stop the process and writes the result to your systems.

Can we use our existing cameras?

Yes. TIM INSPECT is a software platform and works with your current cameras. AXION, VEGA-X and laser measurement are optional, depending on the check.

Which systems does it connect to?

MES, SAP and other ERPs, WMS and PLCs. It takes the expected value from the system and writes the result and evidence photo back.

How fast is a decision?

On AXION a check takes about 1.5 seconds per operation. With the VEGA-X glove, TIM INSPECT decides in under 4 seconds end to end.

How does a project start?

In four steps: discovery, models and integration, a field trial with three metrics defined up front, then rollout and training. We need sample parts and images, system access and a process owner.

Choose your first check point

Tell us which assembly error costs you most. We will decide together which solution, device and system connection fits.

Chat on WhatsApp WhatsApp'tan yazın