You can run a warehouse inventory count without shutting down by moving from one big annual stocktake to counts that happen while normal work continues: a worker walks the aisle with a wearable camera device, rack and pallet labels are read in bulk, and each location is compared with the system record on the spot. Variances such as empty locations, misplaced pallets and unlabeled pallets are then corrected or flagged during the count instead of surfacing days later.
For many warehouses the physical count is still the most disruptive week of the year. Inbound and outbound stop, extra staff are pulled in, and every pallet is scanned one by one. The gap between rack and system then appears all at once, long after anyone can remember why. This guide looks at why that happens and how an approach like Inventory Counting with TIM INSPECT changes the order of events: read first, compare immediately, fix while you are still standing in the aisle.
A full physical inventory has a simple goal: confirm that every location holds what the warehouse management system or SAP says it holds. The difficulty is in the method.
The real cost is not only the lost shipping days. It is the inaccurate stock that drives wrong replenishment, failed picks and the next round of searching for "lost" pallets.
The classic stocktake gives a full snapshot but freezes the operation. It also concentrates all corrections into a single stressful period, which is exactly when mistakes are most likely.
Counting a few aisles at a time avoids a full shutdown, but the work is still one scan per pallet, and the comparison with the system often happens in a back-office report rather than in front of the rack.
Autonomous robots and drones are also used for inventory counts in the industry. They can be a good fit for some layouts, but they add new equipment to the floor. A wearable approach takes a different route: the count is done with your existing team, who already know the warehouse.
In the Inventory Counting scenario on the TIM INSPECT platform, the count is built around four simple steps.
| Situation | What the worker sees | What goes into the record |
|---|---|---|
| Misplaced pallet | AXION shows where the pallet is recorded in the system and where it actually stands on the rack. | The location mismatch is saved to the count record without waiting for the end of the count. |
| Unlabeled pallet | AXION flags a pallet it cannot match to a label. | The variance is flagged for follow-up with its photo. |
| Empty location | A location that should hold a pallet is empty, and AXION alerts. | The empty location is recorded as a variance. |
Because every variance is visible during the count, the person who finds it is also the person best placed to fix it: move the pallet to its correct location, or flag the record for a supervisor. The result is a count record that shows when each location was counted, how each variance was closed and the photo taken at the time.
A worker on foot reads the lower and middle levels comfortably. On high racks, upper locations may need a fixed or forklift-mounted camera. That need is defined on site before the pilot, based on rack height and label layout, so the scope matches your warehouse rather than a generic template.
Bulk reading depends on labels that are present and legible. Review where rack and pallet labels sit, how consistent they are and which areas already have known labeling gaps. Unlabeled pallets are part of the scenario, so the count will surface them rather than skip them.
The value of a walking count comes from comparing reads with location records in real time. Plan the connection to SAP or your warehouse management system early: which location records are compared, and where the count result and its variances are written back.
Count photos are stored with the record. If people or confidential information appear in a photo, the image is filtered, and the retention period is agreed with you. The process is designed in line with GDPR and KVKK requirements.
The solution page describes a scenario, not proven result figures, so define your own metrics at the start. Typical candidates are the time needed to count a set of aisles, the number of variances found during the count rather than afterwards, and how many of them were closed on the spot.
If your bigger issue is verifying pallets as they move rather than where they sit, the related Four-Side Pallet Scanning scenario reads labels on all sides of a pallet in motion.
Yes, when the count is split into aisle-level tasks that a worker completes while operations continue. Bulk reading with AXION removes the need to scan every pallet one by one, so the count fits around normal work.
Empty rack locations, pallets recorded at another location in the system and unlabeled pallets. When one is seen, AXION vibrates and shows it, and the worker corrects or flags it on the spot.
Upper locations may need a fixed or forklift-mounted camera. The need is defined on site before the pilot, based on rack height and label layout.
The count result is written to SAP or the warehouse management system, and the count photos are stored with the record.
To see how a walking count would fit your rack layout and warehouse system, explore the Inventory Counting scenario or request a demo with our team.