Insigtful Blog Pages of Thread in Motion

PPE Detection with Vision AI: Compliance Beyond the Shift Start

Written by Işıl Özyiğit | Nov 17, 2026, 1:30:16 AM

PPE detection with vision AI checks whether people in a work area are wearing the protective equipment that area requires, such as a helmet, vest, safety eyewear or gloves, throughout the shift and not only at the gate. Cameras compare what each person is wearing with the area's rule, and if something is missing, the worker hears exactly what to put on. TIM INSPECT PPE Detection works this way, with alerts delivered to the worker's own wearable device and compliance reported by area and shift.

Why PPE compliance slips during the shift

On most sites, protective equipment is checked by eye at the start of the shift. Everyone walks in with a helmet and a vest, the check is done, and the day begins. What happens afterwards is much harder to see. Safety eyewear gets pushed up onto the forehead in a hot area, gloves come off for a fiddly task and stay off, a worker walks from a low-risk zone into one that needs a mask.

The rules themselves make this harder. Each area has its own required equipment, so the same person may be compliant in one hall and not in the next. Employers are expected to select suitable PPE based on their risk assessment and to make sure it is actually used; the UK Health and Safety Executive's guidance on PPE at work is a good overview of those duties. The gap is between the rule on paper and what people wear at 3 p.m.

Traditional PPE checks and their limits

  • Start-of-shift checks. Useful, but they cover a single moment. Equipment removed later goes unnoticed.
  • Supervisor rounds and spot audits. They catch what the supervisor happens to see, depend on the supervisor's time, and turn into confrontations more often than reminders.
  • Signs and posters. They set expectations at the area entrance but cannot tell a specific person what is missing.
  • Paper audit forms. They produce a percentage once a week or month, too late and too coarse to change behaviour on a given day.

How vision AI handles PPE detection

The TIM INSPECT workflow has four steps:

  1. Define the area rule. Required equipment is set for each work area: helmet, vest, eyewear, gloves, mask or safety harness. The check always follows the rule of the area the person is in.
  2. Detect the equipment. Cameras detect the person entering the area and the equipment they are wearing. Equipment status is assessed, not identity.
  3. Alert when something is missing. The worker's AXION vibrates and names the missing item, for example: "Eyewear missing. Please put on your eyewear." Repeated cases are sent to the shift supervisor.
  4. Report compliance. The alert closes once the equipment is on. Compliance is reported by area and by shift.

The difference from a siren or a screen on the wall is that the message is personal and specific. The worker does not have to guess which rule applies or who the alarm is for; the device on their hand tells them what is missing, and the record closes as soon as they put it on.

Beyond "is it there?"

Wearing equipment is not always the same as wearing it correctly. Depending on the camera view on site, correct-use checks such as a fastened chin strap or a connected harness hook can also be assessed. For work at height specifically, see Working-at-Height Safety.

Connecting to access control

Where needed, PPE detection can connect to an entry turnstile or door controller, so the door stays closed while required equipment is missing. The integration scope is planned around the access system already on site.

What to consider before installation

  • Area rules first. Write down the required equipment for each area before thinking about cameras. Clear, consistent rules make the detection and the reporting meaningful.
  • Camera placement. Entry points and work-area cameras need a clear view of the head, torso and hands. Light, distance and angle decide which items can be checked reliably, so the scope depends on the camera view.
  • Escalation. Decide when a repeated finding goes to the shift supervisor and how supervisors should follow up. The aim is fewer missing items, not more alarms.
  • Privacy. This scenario does not use face recognition. Images are filtered and only the event moment is stored, and privacy is designed in from the start in line with KVKK and the GDPR. Involve employee representatives early.
  • Using the reports. Records show which area and which item an alert was opened for and when it closed. Repeated findings by area and shift help you fix the cause: missing equipment stock, uncomfortable eyewear or a confusing area boundary.

PPE detection often pairs with Restricted-Zone Detection, which handles areas nobody should enter without authorisation. Both are part of the TIM INSPECT platform. More detail and interactive examples are on the PPE detection page.

FAQ

Does the system use face recognition?

No. It assesses the status of the equipment, not who the person is, and stores only the event moment.

Which equipment can be checked?

Helmets, vests, eyewear, gloves, masks and safety harnesses. Correct-use checks can also be assessed, depending on the camera view.

Can each area have different rules?

Yes. The required equipment list is defined per area, and the check follows the rule of the area the worker enters.

Does it work with doors and turnstiles?

It can connect to an entry turnstile or door control system, so the door does not open while required equipment is missing.

Next step

If you want to turn your area rules into a pilot, request a demo and we can review your areas, equipment lists and camera views together.