Skipped assembly steps are cheapest to catch at the station, while the unit is still in front of the worker, not at end-of-line testing or after delivery. A fixed overhead camera that follows every step against the defined standard work can flag a missing, repeated or out-of-order step the moment it happens. That is the idea behind assembly sequence verification with vision AI.
Manual assembly is still the backbone of many lines, especially where variants change often. The work is defined in a standard work instruction, yet nobody measures whether each unit actually followed it. This guide explains why skipped steps slip through, where traditional checks fall short and how a camera-based approach closes the gap.
A skipped step rarely announces itself. A gasket that was never placed, a clip that was pushed in with one hand instead of seated with two, a washer fitted after the cover instead of before it: the unit still looks finished. The error usually surfaces at an end-of-line test, sometimes later in the field.
The further downstream a defect travels, the more it costs. At the station it is a few seconds of correction. At end of line it means rework, tear-down and re-test. After shipment it becomes containment, sorting at the customer, warranty claims and a difficult conversation about traceability. Because the root cause is a missing action rather than a faulty part, it is hard to trace without a record of the station.
Most plants combine several methods. Each helps, but none sees the whole process on every unit.
Camera-based assembly sequence verification watches the station on continuous video and evaluates the whole process, not just the final picture. In the TIM INSPECT assembly sequence scenario the workflow has four parts.
The steps are defined in the system: their order, the part to pick, the tool to use and the method. For example, "place the gear, tighten the gear with the ratchet wrench, place the gasket, place the plate, seat with both hands." The camera follows the same sequence on every unit.
An overhead fixed camera sees the hands, the parts and the tools in the work area. The vision model recognises which part the hand picks, where it is fitted and which tool is used, marks each step as it happens and measures its duration.
When a step is skipped or repeated, the order breaks, the wrong part is picked, a different tool is used or the method differs from the definition, the event is raised immediately. The worker's AXION wearable vibrates and says which step is missing, for example: "Step three is missing. Place the gasket." The worker goes back, closes the gap and continues.
Each completed unit gets a step record and its video. The unit is released to the next station only when no step is open; where needed, a release or stop signal can go to the line PLC. The record is transferred to the MES per unit, so quality teams can later see which steps a unit went through, in what order, and where a deviation opened and closed. Step times are reported as well, which helps when revisiting work instructions and station layout.
The camera needs a clear overhead view of the work surface, the part bins and the tool. Plan for the worker's own body, which can hide the hands from a poorly placed camera, and for reflections from metal parts or shiny packaging. Steady, even lighting makes recognition more reliable than chasing it with software later.
The system can only verify what is defined. If two methods are both acceptable, say so. If variants share most steps, define where they differ. The scope of detectable deviations is finalised around the actual camera view at the station.
The aim is error prevention, not rating workers. The camera looks at the work zone, the hands, the part and the tool, not at identity, and images are filtered. Which footage is kept and for how long should be defined at the start of the deployment in line with GDPR and local rules. Explaining this to the team, and to employee representatives where they exist, before go-live makes adoption much smoother.
Decide early what goes where: the per-unit step record to the MES, and, if you want the line to enforce it, a release or stop signal to the PLC. The scope of the PLC connection depends on the automation already on site.
If your main concern is whether the right part, label or surface is present rather than the order of work, assembly part verification is the closer fit. Both run on the same TIM INSPECT platform.
No. The purpose is to catch a skipped step or a wrong part before the unit leaves the station. Step times are used to improve instructions and station layout, not as an individual performance assessment.
A photo shows the result. Video shows the order and the method: which part was picked, where it was fitted, which tool was used and how long each step took.
Skipped or repeated steps, a broken sequence, a wrong part, a different tool and work that does not follow the defined method, such as a part that must be seated with two hands being fitted with one. The exact scope depends on the camera view.
The alert stays open and the unit is not released to the next station until the missing step is done. A release or stop signal can also be sent to the line PLC.
If you want to see how this would work on one of your stations, request a demo and we will review your work instructions, station layout and camera view together.